BizJet Brief
Thursday, November 19, 2026
BizJet Brief

Thursday, November 19, 2026

Safety

Ground Stop Update: FAA Official Oversaw and Signed Off on El Dorado Router Work Minutes Before Nationwide Stop, Report Says

An FAA official supervised, tested and signed off on the El Dorado router work eight minutes before the ground stop, The Washington Post reports.

Ground Stop Update: FAA Official Oversaw and Signed Off on El Dorado Router Work Minutes Before Nationwide Stop, Report Says
File photo: FAA / Wikimedia Commons, public domain — the Los Angeles Air Route Traffic Control Center, an FAA en-route facility (not the El Dorado site)

Developing story. This latest update follows BizJet Brief's reports "Ground Stop Update: FAA Switches Off Installed Juniper Routers as Duffy Says Root Cause Is Still Unclear," "Ground Stop Update: FAA Pauses New Router Installs as Senators Demand Testing and Answers on Root Cause," "Ground Stop Update: FAA Names Amarillo and El Dorado Sites as Routers Go to L3Harris Lab; Broadcast Function Shut Off Network-Wide" and "BREAKING: FAA Halts All Departures Nationwide After Communications Outage Hits Air Traffic Control Centers."

An FAA official was on site in rural Arkansas supervising the contractor whose work came just before last Friday's nationwide ground stop. The official also tested the finished work and signed off on it, The Washington Post reported Tuesday, citing a person close to the investigation.

According to the Post, the contractor was switching vital air traffic communications lines from an old copper-wire network to a new fiber-optic one. Eight minutes after the sign-off, the radio network serving much of the country's air traffic control centers began to falter. The FAA then ordered the ground stop, which halted much of the nation's air traffic for 4½ hours.

Mashable, which followed the Post's report, said the El Dorado job also involved replacing a router as part of the FAA's national push to upgrade its communications infrastructure.

Why it matters

Transportation Secretary Sean Duffy has put the blame on contractor L3Harris Technologies, which is leading the FAA's fiber-optic upgrades. The Post's source said that focus on L3Harris overlooked the FAA's own role.

On Saturday, Duffy said the department was looking into whether "incompetence" by L3Harris led to the stop, Mashable reported. When the Post asked for comment, the FAA pointed to what Duffy said at a news conference at the Capitol on Tuesday. There he said he wanted L3Harris to "hire better minds" for the wiring work and that he was considering bringing in new contractors.

The cause is still not confirmed

The person who spoke to the Post said the exact cause of the communications outage has not been confirmed. Duffy said Saturday that the new router in Arkansas was faulty and flooded the network with more than 1,000 connection attempts every few seconds, Mashable reported. FAA and L3Harris officials are studying the device, a Juniper router, according to Mashable's account of the Post report. L3Harris has stopped installing those routers, but dozens are already in service.

As BizJet Brief reported earlier Tuesday, the FAA has switched off the Juniper routers already installed in its network. Duffy has said investigators recreated the El Dorado failure but still do not know its root cause.

Questions about oversight rules

Separately, Little Rock station KATV reported Tuesday that it obtained internal FAA documents showing a change in standard operating procedures that sharply reduced oversight of maintenance at the agency's telecommunications sites, including El Dorado. BizJet Brief has not seen the documents.

KATV said the new procedures are still a draft under review, but an FAA memo dated May 20 last year put them into effect. Before that, contractors had to submit maintenance requests, and the FAA reviewed the possible impacts with airlines before approving work such as copper-to-fiber conversions and router swaps. An anonymous Transportation Department source told the station that the new procedure treats those upgrades as "maintenance notifications," and that the tickets are approved automatically.

KATV also cited a weekend statement from the Professional Aviation Safety Specialists union, which said its technicians "were not involved in the upgrades that led to the ground stop." According to KATV, router maker HPE Juniper Networks says the device worked as configured. It was set to a broadcast function rather than point-to-point, and the company stopped short of blaming the installer.

For Part 91 and 135 crews

None of this changes conditions in the air tonight. There is no ground stop in effect, and the FAA says the network is stable while the newer routers stay switched off. But the report shows the investigation is now looking at the FAA's own sign-off process as well as the contractor. Until a root cause is published, crews should keep checking NAS Status before each leg and keep a short contingency plan ready for a sudden departure stop.

BizJet Brief will update this story as the FAA, L3Harris or investigators release more.

Sources

  1. The Washington Post: FAA oversaw and signed off on repair work before nationwide ground stop (Nov. 17, 2026)
  2. Mashable: FAA official oversaw router work just before nationwide ground stop, report claims (Nov. 18, 2026)
  3. KATV: Internal documents reveal FAA reduced maintenance oversight before ground stop (Nov. 17, 2026)
  4. FAA: Nationwide Ground Stop: Questions and Answers
  5. FAA National Airspace System Status