FAA Proposes Landing Gear AD for Falcon 50, 2000 and 2000EX Over Torque Link Defect
A proposed FAA AD would make Falcon 50, 2000 and 2000EX operators replace main gear with suspect torque links before 7,100 cycles. Costs and timing.
The FAA wants owners of three popular Dassault Falcon models to check their main landing gear for parts that may have been damaged when they were made, and to swap out any affected gear before it reaches a new, shorter life limit.
The proposed airworthiness directive, published in the Federal Register on Nov. 12, covers every Mystère-Falcon 50, Falcon 2000 and Falcon 2000EX. The FAA counts 683 of those airplanes on the U.S. registry and estimates that up to 178 of them have an affected part installed.
For crews who fly these types, the proposal is not a grounding and does not call for any immediate inspection flight. But it could put a landing gear change on a flight department's maintenance calendar, with a price tag that AvWeb noted can top $300,000 per airplane.
What the FAA found
According to the proposal, the AD was "prompted by a reported quality escape," meaning a manufacturing problem that got past quality control. Investigators determined that "high-temperature oxidation of main landing gear (MLG) upper and lower torque links may have occurred during manufacturing."
Torque links, sometimes called scissor links, are the hinged arms on each main gear leg that join the upper part of the shock strut to the lower part. They let the strut compress and extend on landing while keeping the wheels pointed straight ahead.
The FAA's wording on the risk is direct: "The unsafe condition, if not addressed, could result in failure of the MLG, possibly resulting in damage to the airplane and injury to occupants."
Neither the FAA nor EASA identified any accidents or in-service gear failures linked to the defect, AvWeb reported.
Europe acted first
The U.S. proposal follows EASA AD 2026-0012, which the European Union Aviation Safety Agency issued on Jan. 19, 2026, and which took effect in Europe on Feb. 2. France, where Dassault is based, is the state of design, so EASA leads on airworthiness actions for Falcons. The FAA proposes to adopt the European directive by reference, with a few small changes.
EASA said the investigation "determined that a reduced life limit must be defined for affected parts." Its directive lists the affected torque link assemblies by part number and serial number, for both left and right main gear, and points operators to the matching Dassault service bulletins: SB F50-557 for the Falcon 50, SB F2000-464 for the Falcon 2000 and SB F2000EX-516 for the Falcon 2000EX.
EASA also noted that the Falcon 50 was included "due to similarity of design."
What the directive would require
Under the EASA directive the FAA would adopt, any airplane with an affected main landing gear must have that gear replaced with a serviceable unit before the affected part passes 7,100 flight cycles since it was first installed on an airplane. One flight cycle is one takeoff and one landing.
A "serviceable" gear, in the directive's terms, is either one that does not carry an affected part, or one that does but whose affected part still has fewer than 7,100 cycles. The directive also limits when an affected gear may be installed on another airplane, so a gear set swapped between tails stays tracked against the same limit.
What it could cost
The FAA's cost table estimates 36 work-hours at $85 an hour, or $3,060 in labor, plus up to $300,000 for a new main landing gear. That puts the maximum at $303,060 per airplane and up to about $53.9 million across the 178 U.S. aircraft the agency expects to be affected.
There is a cheaper path. The FAA said operators could instead rebuild the gear by replacing the upper and lower torque link assemblies, at an estimated $48,990 in parts. And the agency added that, "according to the manufacturer, however, some or all of the costs of this proposed AD may be covered under warranty."
Comment period
This is a proposal, not yet a final rule. The FAA is taking public comments through Dec. 28, 2026, under Docket No. FAA-2026-13805 at regulations.gov. The final AD could change based on those comments, and its compliance clock would run from the final rule's effective date, not EASA's.
What it means for crews
Pilots and flight attendants won't perform this work, but crews on Falcon 50, 2000 and 2000EX aircraft can help their departments stay ahead of it:
- Ask whether your tail is affected. Your director of maintenance or management company can check the torque link part and serial numbers against the EASA list.
- Know the cycle count. The limit is measured in flight cycles, not hours. Short-leg operations, like shuttle or frequent repositioning flights, build cycles faster than long trips.
- Plan for downtime. A main gear swap means the airplane is in the shop. Schedulers and charter sales teams should know early if a trip calendar needs to work around it.
- Report what you see. As always, write up any unusual gear behavior on the ground, like shimmy, abnormal noises or uneven strut extension, so maintenance can look at it.
BizJet Brief will report when the FAA publishes a final rule.